DISCONTINUED Davicom DV-Mini Remote Control And Monitoring System

Davicom Logo




Davicom DV Mini



DV-Mini units have been optimized for systems where the number of Inputs/Outputs is limited, and are non-expandable. They are the perfect choice for sites having only one transmitter.

Connectivity Options:

Product Code Hardware Site Connection
DV-Mini-1 Internal dial-up modem; andEthernet connection for IP – Landline telephone- Analog mobile Telephone (with RJ-11 connector)- GSM (Hayes compatible)- Satellite (Hayes compatible)- Microwave/Radio Link- Internet, WAN, LAN over secure IP
DV-Mini-2 Serial port to accomodate an external Hayes-compatible modem1 (modem not included);Ethernet connection for IP – Landline telephone- Analog mobile Telephone (with RJ-11 connector)- GSM (Hayes compatible)- Satellite (Hayes compatible)- Microwave/Radio Link- Internet, WAN, LAN over secure IP



DV-Mini units now use industry-standard 50-pin Champ connectors for all its Input/Output points.
Remote Control, Monitoring And Interrogation
Ethernet jack #1 allows fully integrated IP capability, including the ability to send alarm messages through e-mail;
Telephone jack allows remote control/monitoring/interrogation through landline. Monitor audio inputs live over the phone and send commands using DTMF tones;
Serial port IOIOI-2 allows remote control/monitoring/interrogation through a GSM, satellite or landline external Hayes-compatible modem.
Local Control, Monitoring And Interrogation
USB port to connect to a laptop (from the DV-Mini’s front panel);
Serial port to connect to a laptop or PDA2 (from the DV-Mini’s front panel);
Stereo headphone jack to locally monitor audio inputs (from the DV-Mini’s front panel).
Site Maintenance
Local and pause push buttons (on the DV-Mini’s front panel) allow on-site technicians to work safely.
On-site Ancillary Equipment
Ethernet jack #2 can ping up to 32 on-site ancillary equipment;
Auxiliary serial port can control an on-site ancillary equipment in pass-through mode;
Auxiliary serial port can monitor for specific alphanumeric strings from an on-site ancillary equipment 3.
On-site Peripherals 
USB port to connect, for example: external memory for data logging, an external modem, etc.3
Plug for an AC/DC converter to monitor power fail on mains.1 Only one external modem can be installed (with or without the optional internal modem). No voice interface and no DTMF control when the external modem is used.2 Serial port adapter for PDA not included.3 On future firmware releases.

Technical Specification

Technical Specification

Electrical Specifications:

Specification Number Description
Metering (Analog)Inputs 8 Resolution: 12 bits;Bipolar/Differential;3 selectable ranges: -2.5 to +2.5, -10 to +10 and -20 to +20 VDC;4-20mA input mode jumper selectable;Impedance > 100 kOhms;Audio Rectifier circuit jumper selectable.
Status (Digital)Inputs 16 EIA compatible;Opto-isolated;Impedance > 22 kOhms;Detection Levels: -12 to 0.8 VDC (low), +2.4 to +12 VDC (high).
Audio Inputs 2 -20 to +10 dBm (300-3000 Hz);Impedance 10 kOhms.
Outputs (Commands) 8 Selectable NO/NC dry contact relays (70 VAC @ 0.4A, 30 VDC @ 2A) or open collector (100 mA)
Auxiliary DCOutputs 1 5 VDC @ 250mA max, 12VDC @ 500mA max >> Total combined 750mA max
Local Access Port 1 115200 bps, DB9 female connector located on front panel; or115200 bps, USB type B connector located on front panel.
Serial Ports forOn-Site AncillaryEquipment 1 1200 to 115200 bps, DB9 male connectors located on rear panel.
Extra Serial-Portsfor On-Site AncillaryEquipment throughUSB Hub & Dongles 8 1200 to 115200 bps, DB9 male on USB dongles connected through USB hub.
Serial Ports forExternal Modems 1* 1200 to 57600 bps, DB9 male connector located on rear panel.* Only available if internal modem is absent
Extra Ports forExternal Modemsthrough USB Hub 4 USB modems required. Must support Linux CDC drivers.
Internal Modem 1 RJ-11 jack located on rear panel;Voice/Fax/Data;56 kbps maximum;Fax up to 14400 bps;DTMF interface.
External USBStorage throughUSB Hub 4 Up to 4 external USB memory devices. FAT32 formatted devices only.
Real Time Clock(RTC) TCXO: 3.8 PPM from -10°c to +60°c. Equivalent to 10 seconds per month.
Power Requirement 11.5 – 14.5 VDC, 1.5 A Max.
Fuse 250 V, 3 A.
Electric Fields Tested to 10 V/m.
ElectrostaticDischarge (ESD) Tested to 12 kV.
Operating TemperatureRange 0 to 50°c (32° to 122°F)-40° to 70°c (-40° to 158°F) available

RoHS Status: RoHS Compliant

Product Resources

Comments are closed.